Webley MkVI Service Revolver

The first batch of Webley revolvers, also known as “Self-Extracting” or “Top-Break” revolvers, arrived in Thailand at the end of last year. Proving to be quite popular, I unfortunately missed out and so had to wait until completion of both the Chinese New Year and Songkran festivities to take possession of my very own Webley MkVI. The wait was definitely worth it.

This is the 6mm smoothbore version marketed in Asia, under licence, by Gun Heaven of Hong Kong and Taiwan. As far as I am aware, it is identical to the 4.5mm version except for the calibre and the fact that it does not have a safety switch fitted to the right-hand side (I note some models have such a safety fitted just above the trigger; although unobtrusive, I am of the opinion that it is unnecessary: if you are ready to shoot and then change your mind, you simply lower the hammer, remove the “cartridges” and place the pistol safely in a holster or otherwise out of harm’s way).

w1

Real Steel Background

Webley & Son of Great Britain, who would later become known as Webley & Scott following a merger in 1897, started development of their famous “Top-Break” revolvers in the 1870s for both military and civilian markets. All were chambered for the substantial .455 inch calibre cartridge with heavy 265 grain bullets travelling at a little over 600 fps. Black-powder cartridges were used in the MkI which appeared in 1887 and replaced the Enfield revolver as standard issue to the British Army. Black powder continued to be used until the MkV in 1894 when smokeless cordite ammunition was introduced (source: world.guns.ru).

The MkVI was the pinnacle of the Webley Top-Break design featuring a six-inch barrel (previous versions had either four or five inch barrels), squared instead of more rounded “bird’s beak” grips and a removeable front post (although this is cast as part of the barrel on the replica). Whilst the earlier MkIV was known for being used extensively during the Boer War, the MkVI became synonymous with The Great War, entering service with British and Commonwealth troops in 1915. Although production of the MkVI by the Royal Small Arms Factory at Enfield ceased in 1932 (Webley & Scott had stopped production in 1921), this powerful revolver was still to be relied upon by soldiers in World War Two alongside its replacement, the Enfield No.2 MkI (source: Wikipedia).

Gun Heaven Webley MKVI

w26

Packaging and Presentation 4.5 / 5

The gun is held securely in place using bubble-wrap inside an attractive cardboard box. Six “cartridges” are provided along with a detailed user manual that covers operation, field-stripping, a specification comparison between the CO2 replica and the “real steel” … and film and game credits! This last one is a rather novel idea, but hardly surprising seeing as how this pistol has featured in so many films over the years.

w2

Excerpts from the User Manual (2014 – far left) … and Small Arms Training Pamphlet, Vol.I, No.11 (1937)

w3

This movie list is repeated on the back of the box along with a brief history of the original firearm. From “The Lost Patrol” to “A Million Ways to Die in the West” (have not seen that one… yet!) and from “Doctor Who” to “Dad’s Army” (two of my favourite shows as a boy… and ones which I am revisiting in middle age!) the Webley Mk VI Revolver has featured in so many productions (even when it should not have, owing to the fact it did not yet exist!) that it is extremely difficult – nigh impossible! – to know which to illustrate here. However, it would be ridiculous not to give at least a couple of examples; so courtesy of that fountain of knowledge the “IMFDB”…

w4

Col. Durnford (Burt Lancaster) taking aim (both eyes open) in “Zulu Dawn” …

w5

… and she’s got two! Anna Barnes-Leatherwood (Charlize Theron) in “A Million Ways to Die in the West” (… and who said shooting is just for boys!)

w6

and finally a shot (excuse the pun!) from a film set in this part of the world — Captain Hornsby (Denholm Elliott) traipsing through the jungle in “Too Late the Hero”

Another excellent idea – and one which I have not seen before – is the inclusion of the facsimile Small Arms Training Pamphlet (Vol. I, No.11) dated 1937, specific to the Webley MkVI. However, the only reason I have not given full marks (and I am being very “fussy” here!) is I would love to see an imitation cartridge box provided with replicas of such historically important guns. Admittedly, I have only ever seen this with the Tokyo Marui 1911A1, but it struck me as being another rather enterprising idea.

Visual Accuracy 8.5 / 10

This replica is, at first glance, identical to the original firearm. My first thoughts were, should you be the curator of a museum wishing to save a little money, then you need look no further than the Webley MkVI replica!

However, there are some very minor differences which I will highlight here. I should like to stress that none of these were at all immediately apparent. The photos with the blue background are part of a larger collection of immaculate British revolvers I found at the “TIR et COLLECTION Armes Règlementaires” forum, a link to which is given at the end of this review.

w7

Photo (top) courtesy of tircollection.com

On the left-hand side everything would appear to be exactly the same, accept for the hammer which, when at rest on the replica, sits slightly proud of the firing pin. Mine comes in what is known as a “weathered” finish and, in my opinion, adds significantly to the authenticity of the gun. The original usually featured a selection of proofing marks and stamps – for example, on the cylinder cam as given above – which are not on the replica. Furthermore, the rear sight appears to be slightly higher, but that may well be intentional as it shoots using a perfectly balanced sight picture.

w8

Three well-defined stamps/ engravings may be found on the left-hand side of the frame. Both the “Mark VI” stamped above the cylinder and the “Webley” patent stamp, correctly identified as 1915, below the cylinder are exactly as would be found on the cartridge firing original; having the calibre stamped on the barrel is something I have not seen, at least on the images I have found, but in my opinion does not look at all out of place.

After all, it could be to distinguish it from the MkIV, reintroduced in 1942 in .38 inch calibre and which bears more than a passing resemblance to a scaled-down MkVI — if one of those is in the pipeline, perhaps with an alternative grip style featuring either the “Webley” logo or “bird’s beak” grips — than I for one would certainly like to have the pair.

w9

Photo (top) courtesy of tircollection.com

A few other minor discrepancies are also noticeable on the right-hand side; namely a screw instead of a pin on which the barrel catch pivots and a pin missing to the rear of the cylinder near the top of the grips. The grips on the replica are of black plastic; I assume Bakelite would have been used on the original. Also, as mentioned previously, the front post is cast as part of the barrel whereas it is held in place by a screw on the original.

The serial number is stamped on the frame above and to the rear of the trigger guard. It actually took me some time to find out exactly where they were placed on the original. My search culminated with the Imperial War Museum website and the Webley MkVI used by author J.R.R Tolkien during World War One (a link to the IWM website is given at the end of this review):

w10

Photo courtesy of the Imperial War Museum, London: © IWM (FIR 11492)

As can be seen, the serial number was stamped on the edge of the cylinder (photo above) as well as underneath the gun, forward of the trigger guard (photo below):

w11

Photo courtesy of the Imperial War Museum, London: © IWM (FIR 11492)

N.B.: The screw for the trigger guard is not included on the replica

The shells, whilst marked “Webley .455” are nearly the same size as those of the “.38 inch” WinGun “7-Series” with an outside shell casing diameter of 9.6 +/- 0.05 mm for the Webley as against to 9.4 mm for the WinGun. However, the lead-coloured rubber “bullet” into which the BB is fitted is slightly shorter than that of the 7-Series “.38” (I believe the “7-Series” is what the Dan Wesson replicas are based upon).

w12

Left to right: WinGun .177, WinGun 6mm, Webley 6mm and Nagant M1895 6mm

Please note that some Webley 6mm shells (not shown) have a smaller diameter hole which will reduce muzzle velocity

w13

It certainly looks the part… and performs, too

Operational and Functional Accuracy 15 / 15

Apart from using CO2 as a propellant, operation is exactly the same as that of the original. A CO2 capsule is inserted by removing the right-hand side grip. There is a notch in the base for this purpose. The lanyard swivel, which doubles as a piercing screw, is then gently tightened without piercing the capsule. I then like to replace the grip before tightening the screw further in order to pierce the CO2. Capsules are pierced cleanly and efficiently and it holds its charge well.

BBs are pushed into the front of each “cartridge” and held firmly in place by the rubber “bullet”. Pressing on the barrel catch allows the barrel and cylinder to swivel forward. Cartridges are then loaded – if dropped into place there is a faint metallic “ring” – and the barrel/ cylinder swung back into place with a positive, metallic “click”. You really could be forgiven for forgetting this replica is made of alloy as against steel!

w14

The Webley MkVI, as per the original, may be fired in both single and double action. Once firing has been completed, the cylinder is again swung open and the cartridges raised automatically by the extractor. If the barrel is pushed fully forward, then the extractor will return to its closed position.

w15

A shell being extracted. Although marked “.455” it is in fact more akin to a .38”

Inset: BBs are held firmly in place by the rubber “bullet”

Field-stripping instructions are provided in the user manual. This is much more straightforward than I imagined it would be. With the shells removed, the bottom screw below the cylinder cam assembly is removed and the cam rotated in a clockwise direction. The cylinder then “pops-up” when the barrel is fully opened and can be removed.

w16

Indicating the screw which unlocks the cylinder cam

w17

Shooting 35 / 40

Most of my shooting to date – nearly 600 rounds through six CO2 capsules – has been done in single-action using both a one and two handed grip (the targets shown have all been using two hands). Double-action was a little stiff at first, but is improving with use and practice. The pistol has a real “heft” to it, although with a tendency to fall forward if not held with a firm grip; just like the original, I should imagine. I weighed mine using digital scales and, correcting for spent CO2, this came to 1062 grams (loaded) which equates to 2.34 lbs (an original would be 2.4 lbs, unloaded).

The fixed sights provide a good, clear sight picture; even in low light and without my specs on! As mentioned previously, the rear sight is slightly higher on the replica, but I should imagine this is intentional as it results in a point of aim equaling point of impact.

w18

If target shooting, then the front post should be in focus, not the rear sight.

A clear sight picture with POA (top of post) = POI

I initially shot using .25g (FireFly) BBs. Although obtaining reasonably good results at six yards with a grouping of about 1.5 to 2 inches and mean score of 37 based on sets of five shots at the standard Umarex Boys Club target, which is scaled for use at this distance, I soon discovered that heavier .40g (FireFly) balls resulted in a marked improvement as shown in the following photo:

w19

.40g 6mm BBs at six yards using a two-handed grip.

The grouping on target four is ⅝ inch centre to centre. The inset shows the chrono reading from shot #41

Although muzzle velocity was rather inconsistent for the first few shots, it soon settled to approximately 370 +/- 20 fps using .40g 6mm BBs in a relatively cool (for Thailand!) 27°C. In fact, by about half-way through the capsule of CO2, readings were even more consistent at around 385 +/- 5 fps. At least 90 goods shots may be had from a capsule of CO2. However, it had been a few days prior to this that I first decided to swap to the heavier ammunition… just after I had shot my 10m UBC competition!

w20

All shot at 10m. The targets on the left using .25g, the rest using .40g.

The target in the centre, whilst not being a high score, has groupings of 1 ⅜ inch and ¾ inch (not counting the flier) top and bottom respectively

Whether it is a little less powerful than the 4.5mm version, I am not sure. It is certainly perfectly adequate for my needs, being just right for my “Biscuit Tin” range with shots easily connecting with the single lid which presents an eight inch diameter target at twenty yards. What is also worthy of note is that, thanks to the slightly higher power than is usually associated with 6mm replica guns, on pulling the trigger you immediately hear the impact against the tin lid in the distance, making it much more suitable (and fun!) for plinking in the garden (neighbours permitting).

w21

There is even a puff of “smoke”, noticeable at night, from the  rear of the cylinder and barrel. Whether this might indicate an imperfect seal between the CO2 valve and cartridge, I would not like to say as the pistol is remarkably efficient in its consumption of CO2 and the marriage between the two with the cylinder closed appears to be fine; anyway, it looks kind of cool. The pistol is not particularly loud.

w22

Quality and Reliability 14 / 15

It is really too soon to form a proper opinion, but to date the pistol has operated flawlessly. What has to be remembered is that, although no doubt made of a very good quality and durable alloy, it is still made of alloy and not steel. The only thing I could mention is that there is a very slight lateral movement in the barrel where it pivots with the frame, but this is not worsening with use and disappears when the barrel is snapped shut. Furthermore, I would be very surprised if the original did not have some minor movement at this point, too — these guns were built to operate in the worst conditions possible; reliability as opposed to fine tolerance was the order of the day.

w23

The cylinder comes lightly greased and there are no signs of wear to the pawl teeth.

Right – view through the smooth bore barrel

w24

The wide indexing pawl, cylinder stop and valve gasket.

Right – Please note the steel insert in the hammer where it strikes the “firing pin” (this reinforcing pin is to be found on all the WinGun/ Gun Heaven replicas I own)

Overall Impression 15 / 15

I have decided on full marks for this section since, if anything, this pistol has surpassed my expectations — and they were high. Having been so impressed by this smoothbore version of the Webley MkVI, I must admit that I am more than a little keen to see the .177 pellet version one day. Also, as mentioned above, should the manufacturers decide to modify things somewhat to produce a MkIV to accompany the MkVI, then in my opinion they would definitely make a great pair!

Introduced in 1915, this gun was issued to men who were expected to endure the unimaginable horrors of World War One. Most of these men were not professional soldiers, but ordinary people from all walks of life who when called upon, did their duty, many of them never to return home. Terrible sacrifices were made on both sides; not only must this never be forgotten, we must ensure that it never happens again.

On a less serious note, I feel immense credit is due to Gun Heaven/ Toubo/ WinGun and Webley for deciding to work together in order to revisit the original design and thence develop what can only be described as a thoroughly authentic, fully functioning replica of the Webley MkVI Service Revolver; one which should appeal not only to shooters and collectors of replica firearms like myself, but also to those who may otherwise not be particularly interested in replica pistols such as full-bore and other shooting enthusiasts, military historians, readers of classic late 19th and early 20th Century fiction and, last but not least, avid television and movie fans!

w25

Total 92 / 100

Review by Adrian. Adrian is also a moderator for the Umarex Boys Club Forums.

Related pages

Nagant M1895 Revolver review

Umarex Colt Single Action Army revolver review

Home

6mm replica reviews

Links

http://www.tircollection.com/t7678-revolvers-british

http://www.iwm.org.uk/collections/item/object/30034679

tags: webley, mkIV, revolver, replica, co2, 6mm, 4.5mm, gun, heaven, air, pistol, review

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s